Wheel Bearing Seal Replacement Steps

Follow the wheel bearing seal replacement steps for a home hub job, from pulling the old grease seal to seating a new one without damaging the bearing race.

8 min read2 viewsWheel Bearing Seal Replacement Steps
— · 0 votes
Contents
  1. How the wheel bearing seal works
  2. Gather tools and lift the vehicle safely
  3. Remove the hub and pull the old grease seal
  4. Clean and inspect the bearing race and hub bore
  5. Pack the bearing before fitting the seal
  6. Drive the new seal squarely into the hub bore
  7. Check for leaks and set the final torque
  8. Wheel bearing seal questions
  9. How do I replace a wheel bearing seal?
  10. Can I reuse a wheel bearing seal after removing it?
  11. What tool drives a wheel bearing seal in?
  12. Why does a new wheel bearing seal leak?
  13. Do I need to replace the bearing when I change the seal?

Replacing a wheel bearing seal means removing the hub, prying out the old grease seal, cleaning and repacking the bearing, then driving a new seal squarely into the hub bore. The job rewards patience more than force, because a seal that goes in crooked or a race that gets scored will leak or fail. Work on a clean bench and stop if the bearing itself shows wear.

  • Pull the hub off the spindle before any seal work, and keep the outer bearing from dropping.
  • Pry the old grease seal out from the inner side and never reuse a bent seal.
  • Clean and inspect the bearing race and spindle before fitting anything new.
  • Pack the bearing with grease and seat the new seal flush and square to the hub bore.
  • Stop and hand the job to a specialist if a race, spindle or bore is scored or damaged.

How the wheel bearing seal works

A wheel bearing seal sits at the inner end of the hub and holds grease against the bearing while keeping road grit and water out. The seal presses into the hub bore and rides on a smooth surface of the spindle or axle. Its lip must stay flexible and contact that surface evenly.

The same part is called a grease seal or hub seal depending on the supplier, and the three names point to one job. A seal that leaks lets grease escape and lets contamination reach the bearing rollers. Bearing wear then follows, along with noise and play at the wheel.

Seal work belongs with bearing service, not instead of it. Replacing a seal on a dry or rough bearing hides the real problem for a short time. Inspect the bearing and the spindle surface before you decide how far the repair goes.

Gather tools and lift the vehicle safely

A seal job needs a jack and stands, a wrench set, a hub or drum puller where the design calls for one, a seal driver, a brass drift, and a pick or seal puller. A torque wrench matters for the final spindle nut setting. Solvent, clean rags and fresh wheel bearing grease complete the kit.

Lift the vehicle on level ground and support it on stands rated for the load. Never work under a vehicle held only by a jack. Chock the opposite wheels and loosen the lug nuts before the wheel leaves the ground.

Follow the service information for your vehicle on the spindle nut and any locking device. Some hubs use a cotter pin or a staked nut that must be released first. Keep the removed parts in order so the bearing and adjusting hardware go back the same way.

Remove the hub and pull the old grease seal

Hub seal removal starts once the hub is off the spindle and resting on a clean surface. The inner bearing and seal come out from the back of the hub. Catch the outer bearing as you slide the hub off so it does not fall onto the floor.

Drive the inner bearing out with a brass drift applied to the bearing inner ring, not the cage. Working around the ring in small steps keeps the bearing square in the bore. The old seal usually comes free in the same pass or pries out with a seal puller.

Pry a stubborn seal from its metal edge and work around the rim rather than digging at the rubber lip. A seal that resists hard pressure can be cut, but protect the hub bore and the spindle from the tool. Discard the old seal; a bent or stretched seal will not seal again.

Clean and inspect the bearing race and hub bore

The bearing race and hub bore must be clean and free of burrs before a new seal goes in. Wash the bearing in solvent and dry it with compressed air or clean rags. Never spin a dry bearing with air, since the rollers can skid and score.

Look for pitting, bluing, spalling or a rough feel as the bearing turns. Check the spindle surface where the seal lip runs; a groove there lets grease past a new seal. Scored or worn parts call for bearing or spindle replacement, which is specialist work on many vehicles.

Wipe the hub bore and remove any old sealant or metal shavings. A light film of grease on the bore helps the new seal start square. Keep grit out of the bearing area during the whole process.

  • Inspect the bearing rollers and cage for pitting or looseness
  • Check the race for scoring, bluing or a rough feel
  • Look at the spindle seal surface for a wear groove
  • Clean the hub bore and remove burrs or old sealant
  • Replace the bearing or spindle if damage is found

Pack the bearing before fitting the seal

A bearing seal replacement only protects a bearing that carries the right amount of grease. Work fresh grease into the rollers and cage from the wide side of the bearing until it shows at the narrow side. Keep the grease clean and use the type the vehicle maker specifies.

Overpacking a hub can push grease past the seal lip once the wheel turns. Fill the hub cavity partly and leave room for expansion. Too little grease leaves the bearing dry at startup, so follow the service information rather than guessing.

Fit the packed inner bearing into the hub, then add grease to the cavity behind it. The seal goes in next, with the lip facing the bearing. Keep the seal off the bench until the moment it is fitted.

Drive the new seal squarely into the hub bore

A seal driver of the right diameter presses the new seal in by its outer edge and keeps it square. A socket or a block of wood can work if it contacts the seal rim evenly. Striking the seal face directly can bend the metal case.

Start the seal by hand and check that it enters straight. Tap with light, even blows around the rim until the seal sits flush with the hub face or at the depth the service information states. A seal set too deep can block the bearing or miss the spindle surface.

Wipe the seal lip with a little grease and keep the lip clean as the hub goes back on. Fit the outer bearing and the adjusting hardware as the maker describes. Set the spindle nut to the specified torque or end play with a torque wrench.

Check for leaks and set the final torque

After assembly, turn the wheel and feel for roughness or play before the vehicle returns to the road. A correct job turns smoothly with no wobble at the tire. Recheck the lug nuts and the spindle nut torque after a short drive.

Look at the inner side of the wheel and the brake area for fresh grease after a few miles. A leaking seal points to a damaged lip, a worn spindle surface or a seal driven in crooked. Do not ignore a leak because a new seal is in place.

A repair estimate for this job lists the seal, the grease, and any bearing or spindle parts the inspection finds. A shop may also add labor for hub removal and bearing packing. Keep the old parts so the provider can see what failed.

Wheel bearing seal questions

How do I replace a wheel bearing seal?

Remove the hub, pry out the old grease seal from the inner side, clean and repack the bearing, then drive a new seal squarely into the hub bore. Refit the hub and set the spindle nut to the maker's torque. Inspect the bearing and spindle first, because seal work alone will not fix a worn bearing.

Can I reuse a wheel bearing seal after removing it?

No, a wheel bearing seal should not be reused once it is pulled. The metal case bends and the lip loses its grip on the spindle surface during removal. Fit a new seal every time the hub comes apart for bearing service.

What tool drives a wheel bearing seal in?

A seal driver of the right diameter is the correct tool for seating a wheel bearing seal. The driver presses on the outer edge and keeps the seal square in the hub bore. A socket or wood block works only if it contacts the rim evenly and does not touch the lip.

Why does a new wheel bearing seal leak?

A new wheel bearing seal leaks when the lip is damaged, the seal sits crooked, or the spindle surface has a wear groove. Too much grease in the hub can also push past the lip. Inspect the spindle and reseat or replace the seal as needed.

Do I need to replace the bearing when I change the seal?

Not always, but the wheel bearing must be cleaned, inspected and repacked whenever the seal is changed. Pitting, roughness or play means the bearing needs replacement. A worn bearing or scored spindle is work for a trained specialist on many vehicles.

Read next

Latest articles