# Subaru BRZ Clutch Replacement DIY

A practical guide to doing a Subaru BRZ clutch replacement yourself: parts, transmission removal, flywheel checks, the alignment tool and safe limits.

A Subaru BRZ [clutch replacement DIY](/articles/clutch-replacement-diy-steps-and-instructions/) job means dropping the transmission from under the car, unbolting the old clutch, and fitting a new clutch disc, pressure plate, and release bearing. The work is possible on jack stands with hand tools, but the gearbox is heavy and the bell housing bolts are awkward to reach. Read the whole job first and decide which steps you will hand to a shop. 

- A clutch replacement kit for the BRZ includes the disc, pressure plate, release bearing, and an alignment tool.
- The transmission must come out from under the car, so secure lifting and a helper matter more than speed.
- The flywheel surface is checked and resurfaced or replaced while the clutch is off.
- The clutch disc must be centered with the alignment tool before the pressure plate is tightened.
- Pedal free play and fluid are checked after the gearbox goes back in.
 

## What the BRZ clutch job actually involves 

The Subaru BRZ clutch sits between the engine and the manual gearbox at the back of the engine. Replacing it means separating those two units, which is the largest part of the job. The clutch itself is a small stack of parts, but reaching it takes most of the time. 

Plan the job as three stages: get the car safely in the air, remove the transmission, and then swap the clutch parts. Each stage has its own tools and its own risks. A garage with a lift and a transmission jack makes the middle stage far easier than a driveway does. 

The BRZ is rear-wheel drive with a manual gearbox mounted behind the engine. That layout gives reasonable access from below once the car is raised. Treat the job as a full day of work for a careful first attempt rather than an afternoon task. 

## Parts to gather before you start 

A Subaru BRZ clutch replacement kit supplies the clutch disc, the pressure plate, and the release bearing together. Buying them as a set avoids mixing worn and new parts. Confirm the kit matches your model year and engine before the car goes up. 

The flywheel is a separate decision. It may be resurfaced by a machine shop or replaced with a new one, and that choice depends on its condition once it is visible. A rear main seal and the gearbox input shaft seal are worth inspecting while the area is open. 

Small parts add up: new flywheel bolts where the maker specifies them, thread locking compound, and the correct gearbox oil. An alignment tool is often in the kit, and it must match the disc splines. Check every box against the old parts as they come off. 

- Clutch kit with disc, pressure plate, release bearing and alignment tool
- Flywheel resurfacing or a replacement flywheel
- Flywheel bolts if the maker calls for new ones
- Rear main seal and input shaft seal for inspection
- Gearbox oil and thread locking compound
- Jack stands, a transmission jack and long extensions
 

## Getting the car safely in the air 

Safe lifting is the first rule of any Subaru BRZ clutch replacement DIY job. The car must sit on rated jack stands on level ground, with the wheels chocked. Never work under a car held only by a hydraulic jack. 

Raise the front and rear high enough to slide under with room to move. The gearbox comes out downward and rearward, so the car needs clearance along its whole length. A helper who watches the stands and hands you tools reduces the chance of a mistake. 

Disconnect the battery before touching wiring near the gearbox. Support the engine from above or below once the gearbox is unbolted, so it does not hang on its mounts. If any of this feels beyond your setup, stop and book the job with a trained technician. 

## Removing the transmission step by step 

Transmission removal is the step that decides whether the Subaru BRZ clutch replacement DIY job goes smoothly. Everything between the gearbox and the car body must be freed before the unit slides back. Work from the outside inward and keep the fasteners grouped. 

The driveshaft comes off first at the rear flange, then the shifter linkage, the reverse light wiring, and the clutch line or release mechanism. The starter motor and the bell housing bolts follow. Support the gearbox on a transmission jack before the last bolt comes out. 

Pull the gearbox straight back until the input shaft clears the clutch, then lower it slowly. The unit is heavy and unbalanced, so two people or a proper jack are needed. Set it down on a stable surface and never let it hang on the input shaft. 

- Disconnect the battery and label any wiring you unplug
- Remove the driveshaft and tie it aside
- Free the shifter linkage and the clutch release parts
- Unbolt the starter motor and the bell housing bolts
- Support the gearbox on a jack before the last bolt
- Slide the gearbox straight back and lower it slowly
 

## Swapping the clutch disc and pressure plate 

With the gearbox out, the old pressure plate bolts come loose in a cross pattern to release spring tension evenly. The clutch disc and pressure plate then lift away. Note which side of the disc faced the flywheel before you remove it. 

The alignment tool holds the new clutch disc centered while the pressure plate is tightened. Fit the disc and plate over the tool, start the bolts by hand, then tighten them in stages and in a cross pattern. The tool comes out only after the plate is fully seated. 

Mark the disc orientation so the side labeled for the gearbox faces the right way. Wipe the friction surfaces clean and keep grease away from them. Check that the release bearing slides freely on its guide before the gearbox returns. 

## Checking the flywheel while it is exposed 

The flywheel surface is inspected once the clutch is off, because a worn or scored face causes shudder and slipping. Look for deep grooves, heat cracks, and a step at the outer edge. A machine shop can resurface a serviceable flywheel to a clean face. 

A dual-mass flywheel needs a check for free play and smooth rotation within its design limits. If it rocks loosely or shows damage, replacement is the safer route. The choice between resurfacing and replacing depends on the flywheel type and its measured condition. 

Clean the flywheel face with a lint-free cloth and a suitable solvent before fitting the new clutch. Bolt torque and the tightening pattern come from the maker's manual, not from memory. A flywheel that is not seated flat causes vibration that no clutch adjustment can fix. 
| Flywheel option | When it fits | What it needs | 
| Resurface the existing flywheel | Solid face with light scoring and no cracks | Machine shop measurement and a clean finish | 
| Replace with a new flywheel | Deep grooves, heat cracks or a worn dual-mass unit | New bolts where the maker specifies them | 
| Keep the flywheel as is | Face is clean and within specification | Careful cleaning and a torque check |  

## Refitting the gearbox and finishing the job 

The gearbox goes back in only when the clutch disc is centered and the input shaft splines carry a light film of the specified grease. Line the box up square with the engine and slide it forward by hand. Never pull it in with bolts, which damages the clutch and the bearing. 

Refit the bell housing bolts, the starter, the clutch release parts, the wiring, the shifter linkage, and the driveshaft in reverse order. Fill the gearbox with the correct oil if it was drained. Reconnect the battery only after every connection is checked. 

The first start happens with the car still supported and the wheels off the ground. Check for leaks and listen for unusual noise before lowering the car. A pedal that feels wrong at this point means the release mechanism needs attention, not a test drive. 

## Checking the pedal and the first drive 

Clutch pedal free play and bite point are checked after a Subaru BRZ clutch replacement, because a new disc changes where the pedal engages. Adjust the pushrod or cable only as the maker's procedure allows. A pedal that stays on the floor points to air in the hydraulic line or a faulty release part. 

Bleed the clutch hydraulic circuit if the line was opened, using the maker's sequence. Top up the reservoir with the specified fluid and check for leaks at the line and the slave cylinder. Pump the pedal several times and confirm it returns fully each time. 

The first drive stays gentle, with no hard launches and no riding the pedal. Stop and recheck the pedal feel after a short distance. If the clutch slips, shudders, or makes noise, park the car and have a technician inspect the installation. 

## Subaru BRZ clutch replacement questions 

### Is a Subaru BRZ clutch replacement a realistic DIY job? 

Yes, a Subaru BRZ clutch replacement is a realistic DIY job for someone with a safe lifting setup, a transmission jack, and patience. The gearbox is heavy and the bell housing bolts are awkward, so a helper makes the work safer. Anyone unsure about supporting the car or the engine should use a trained technician. 

### What parts does a BRZ clutch replacement kit include? 

A Subaru BRZ clutch kit includes the clutch disc, the pressure plate, the release bearing, and often an alignment tool. The flywheel, flywheel bolts, and seals are separate items. Check the kit against your model year and inspect the flywheel once the gearbox is out. 

### Do I need an alignment tool for the clutch disc? 

Yes, an alignment tool is needed to center the clutch disc while the pressure plate is tightened. The tool matches the splines of the disc and keeps the disc square to the flywheel. Without it, the gearbox input shaft may not slide back in. 

### Can I resurface the flywheel instead of replacing it? 

Resurfacing a Subaru BRZ flywheel is possible when the face is solid and free of cracks, and a machine shop measures it first. A dual-mass flywheel with excess free play or damage needs replacement instead. The right choice depends on the flywheel type and its condition. 

### Why does the clutch pedal feel different after replacement? 

A new Subaru BRZ clutch changes the pedal bite point because the disc and pressure plate are fresh. Free play and the release mechanism are adjusted to the maker's procedure. A pedal that stays down or feels spongy points to air in the hydraulic line or a release fault. 

### How do I know if the job needs a professional? 

The Subaru BRZ clutch job needs a professional when you lack rated stands, a transmission jack, or a second person for the gearbox. Damage to the flywheel, a leaking rear main seal, or hydraulic faults also justify expert help. Park the car rather than drive it with a slipping or noisy clutch.
