# Oil Viscosity Chart: How to Read Grades Across Temperatures and Units

Learn how to read an oil viscosity chart across Celsius and Fahrenheit, in cSt and in SAE grades, and match a grade to your engine and climate.

An oil viscosity chart pairs each SAE grade with a measured thickness at set temperatures, so you can compare a 5W-30 with a 10W-40 at a glance. The number before the W describes cold behavior, and the number after the W describes thickness at operating temperature. The chart turns those numbers into a range you can check against your owner's manual. 

- Read the grade in two halves: the W number for cold starts and the second number for thickness at 100 °C.
- Viscosity in cSt is measured at 40 °C and 100 °C, while SAE J300 sets the limits each grade must meet.
- A lower W number flows more freely in cold weather, and a higher second number stays thicker when hot.
- The same grade appears in Celsius and Fahrenheit charts, so match the unit before you compare numbers.
- Confirm the grade and API service rating in your owner's manual before you buy oil.
 

## What an oil viscosity chart shows 

An oil viscosity chart displays viscosity grades side by side with the thickness each grade must reach at defined temperatures. The chart is a comparison tool, not a single number, because engine oil changes thickness as it warms. Each row or column links a grade to measured limits rather than to a feeling of thickness. 

The viscosity numbers come from laboratory tests that pour or spin the oil at controlled temperatures. Kinematic viscosity in cSt is measured at 40 °C and at 100 °C for the grades in the chart. Cold-cranking viscosity is a separate test that shows how the oil behaves when a starter turns a cold engine. 

A chart labeled in Celsius and a chart labeled in Fahrenheit show the same grades and the same limits. The difference is only the temperature scale printed along the axis. Read the unit before you compare a chart row with a weather forecast. 
| Chart column | What it measures | Unit | 
| Cold-cranking viscosity | Pumping resistance during a cold start | mPa·s at a set low temperature | 
| Kinematic viscosity at 40 °C | Flow thickness when warm but not hot | cSt | 
| Kinematic viscosity at 100 °C | Thickness at engine operating temperature | cSt | 
| HTHS viscosity | Thickness under high heat and shear | mPa·s at 150 °C |  

## How to read a grade such as 5W-30 

A multigrade oil grade such as 5W-30 carries two viscosity numbers that describe two different jobs. The 5W part covers cold behavior, and the 30 part covers thickness at operating temperature. The W stands for winter, not for weight, even though people often say oil weight. 

A lower number before the W means the oil resists thickening in the cold and can be cranked and pumped more easily. A higher number after the W means the oil stays thicker when the engine is hot. The two halves are tested separately and both must pass for the grade to exist. 

The gap between the two numbers shows how wide the operating temperature range of the oil is. A 0W-40 covers a wider span than a 20W-50, because it starts thin in the cold and stays thick when hot. Viscosity index improvers are the additives that let one oil meet both ends of the range. 

- Find the grade on the label, for example 5W-30.
- Read the number before the W as the cold-flow rating.
- Read the number after the W as the hot-thickness rating.
- Check the chart row for that grade against your climate.
- Match the grade to the owner's manual recommendation.
 

## Celsius and Fahrenheit on the same chart 

An oil viscosity chart in Fahrenheit and a chart in Celsius describe identical grades, so the only task is converting the temperature you see. The conversion between the two scales is a fixed formula, not a property of the oil. Water freezes at 0 °C and at 32 °F, which gives a useful reference point. 

To go from Fahrenheit to Celsius, subtract 32 from the reading and multiply the result by five ninths. To go the other way, multiply the Celsius reading by nine fifths and add 32. A winter morning at 0 °F is about minus 18 °C, which sits in the cold end of a chart. 

Cold-cranking limits in SAE J300 are set at temperatures that differ by grade, and those test temperatures appear on charts in one scale or the other. Read the caption of the chart to confirm which scale the test temperatures use. A grade tested at a colder temperature shows better cold performance in the chart. 
| Fahrenheit | Celsius | Chart reading | 
| 32 °F | 0 °C | Cold start reference point | 
| -13 °F | -25 °C | Cold-cranking test zone for low W grades | 
| 68 °F | 20 °C | Mild ambient temperature | 
| 212 °F | 100 °C | Kinematic viscosity test temperature |  

## Engine oil types and grades explained 

Engine oil types and grades answer two separate questions: what the oil is made of and how thick it is. The grade, such as 5W-30, comes from SAE J300, while the API service rating tells you the performance level the oil meets. A label carries both pieces of information. 

Oil types divide into mineral, synthetic blend and full synthetic base stocks, and each type can be built to the same viscosity grade. The grade describes thickness behavior, and the base stock describes how the oil is made. Two oils with the same grade can carry different API service ratings. 

Car engine oil grades explained in a chart still need the owner's manual as the final word. The manual lists the grade and the API service rating the engine was designed for. A chart helps you compare options, but the manual sets the requirement. 

- Grade: the SAE viscosity number, for example 10W-40.
- API service rating: the performance category printed on the label.
- Base stock: mineral, synthetic blend or full synthetic.
- HTHS viscosity: a separate high-heat thickness measure.
- Owner's manual: the source for the required grade and rating.
 

## Viscosity chart versus temperature in practice 

An oil viscosity chart versus temperature shows how one grade thickens as the thermometer drops and thins as it rises. The curve is not a straight line, so a chart plots measured points rather than simple steps. Reading the curve helps you see why a cold start is the hardest moment for oil flow. 

At low temperatures, the oil must stay fluid enough to reach the bearings within seconds of a start. At high temperatures, the oil must stay thick enough to keep a protective film between moving parts. The chart shows both ends, and the grade you pick sits between them. 

Climate matters because the coldest start your engine sees sets the cold requirement. A grade with a lower W number gives more margin in a cold climate. A hotter climate puts more weight on the second number and on HTHS viscosity. 

- Match the W number to the coldest start your engine faces.
- Match the second number to the thickness the engine needs when hot.
- Check HTHS viscosity when the engine works hard or runs hot.
- Keep the grade within the owner's manual range.
 

## Where charts come from and how to print one 

Oil viscosity charts come from the SAE J300 standard, which sets the limits each grade must meet. Oil makers and service publications redraw those limits into a chart for quick reference. A printable viscosity chart PDF is simply a portable copy of the same grade limits. 

A chart from a manufacturer may add columns for its own products or for API service ratings. Compare the grade row and the test temperature, not the brand name on the page. A free download and a printed wall chart should agree on the grade limits because both trace back to the standard. 

Treat any chart without a stated source with care, because a redrawn chart can shift a number or drop a temperature. Check that the chart names SAE J300 and states the temperature scale. A lube oil viscosity chart for industrial oil may use different grade systems than an engine oil chart. 

- Source: look for SAE J300 on the chart.
- Scale: confirm Celsius or Fahrenheit in the caption.
- Grades: check that both W and hot numbers appear.
- Rating: keep the API service rating separate from the grade.
 

## Choosing a grade from the chart 

An oil viscosity chart narrows your choices, and the owner's manual recommended grade settles the final pick. The manual accounts for the engine design, the oil pump and the emission controls together. A chart alone cannot weigh those factors. 

Choose a grade within the range the manual allows for the ambient temperatures you expect. Moving one step in the W number changes cold behavior more than it changes hot thickness. Moving one step in the second number changes hot thickness and fuel economy. 

HTHS viscosity matters when the engine is designed around a specific high-heat thickness, and the manual ties that requirement to the grade. A grade outside the specified range can leave the wrong film at high temperature. Ask a qualified technician when the manual lists more than one acceptable grade. 

## Mistakes when comparing charts 

An oil viscosity chart misread across units or scales gives a false comparison. Mixing a Fahrenheit value with a Celsius row is the first error, because the numbers look plausible but describe different temperatures. Check the scale label before you read a single row. 

Confusing the W half with the hot half is a second error, since the two numbers answer different questions. A larger W number does not mean a thicker oil at operating temperature. The second number carries that meaning. 

Treating the API service rating as a viscosity grade is a third error, because the rating describes performance categories rather than thickness. Reading a chart without the manual is a fourth error, since the manual sets the requirement for the engine. A trained technician can confirm a grade when a chart and a manual disagree. 

## Oil viscosity chart questions 

### What does an oil viscosity chart show? 

An oil viscosity chart shows each SAE grade with the thickness limits it must meet at set temperatures. It links cold-cranking behavior with kinematic viscosity at 40 °C and 100 °C. The chart is a comparison tool that you check against the owner's manual. 

### How do I read a viscosity chart in Celsius? 

A viscosity chart in Celsius lists the same grades as a Fahrenheit chart, with test temperatures printed on the Celsius scale. Read the grade row and confirm the caption states Celsius before comparing it with a weather reading. Convert the value if your forecast uses Fahrenheit. 

### Can I get an oil viscosity chart as a PDF? 

A printable viscosity chart PDF is a portable copy of the SAE J300 grade limits. Check that the file names its source and states the temperature scale before you rely on it. A chart without those details may have been redrawn with errors. 

### What is the difference between cSt and SAE grades? 

Kinematic viscosity in cSt is a measured value at a set temperature, and an SAE grade is a band of limits built from such measurements. The chart links the two, so a grade maps to a range of cSt values. The cSt figure describes a measurement, and the grade describes a category. 

### Does a higher viscosity number mean a thicker oil? 

A higher number after the W means a thicker oil at operating temperature, and a lower number before the W means easier cold flow. The two halves of the grade must be read separately. A 10W-30 is not simply thicker than a 5W-30 in every condition. 

### How do engine oil grades differ from API service ratings? 

Engine oil grades describe viscosity, and API service ratings describe the performance level the oil meets. A label carries both, and the owner's manual lists both requirements. A chart of grades does not replace the service rating.
