Heat Shrink Tubing Size Chart and How to Choose the Right Size
Read a heat shrink tubing size chart the right way: supplied and recovered diameter, shrink ratio, wire gauge and metric sizes, and how to pick a size for a splice.
Contents
- What a heat shrink size chart shows
- Finding the size for your wire or cable
- Using wire gauge to pick a tubing diameter
- How shrink ratio changes the range
- Reading metric and inch sizes together
- Wall thickness and adhesive lining
- Checking heat shrink temperature rating
- Building the line item for an estimate
- Heat shrink tubing sizing questions
- What size heat shrink do I need for my wire?
- How do I size heat shrink tubing for a splice?
- What heat shrink tubing size fits 14 gauge wire?
- Does a 3:1 heat shrink ratio replace two sizes?
- Can I use a heat shrink size chart from another brand?
- How do I convert heat shrink tubing sizes in mm to inches?
A heat shrink size chart is read by matching two diameters, not one. Find the tubing whose supplied inner diameter is larger than the cable or connector it covers, and whose recovered diameter is smaller than that same part after shrinking. The gap between those two numbers, set by the shrink ratio, decides which sizes can grip your wire.
- Measure the widest part the tubing must slide over, then pick a supplied inner diameter above it.
- Check that the recovered diameter is below the part so the tubing grips after shrinking.
- A 2:1 ratio halves the diameter, while 3:1 and 4:1 cover a wider range with one size.
- Use the wire gauge to tubing diameter table as a starting point, then confirm with a caliper.
- Choose a wall thickness and adhesive lining that match insulation and sealing needs, not just fit.
What a heat shrink size chart shows
A heat shrink size chart lists the numbers that describe each tubing size before and after heating. The supplied inner diameter is the opening of the tubing as it arrives, and the recovered diameter is the opening once it has fully shrunk. The chart also gives the shrink ratio and the wall thickness after recovery.
These figures come from the tubing maker, so a chart for one brand does not transfer to another. A Raychem heat shrink chart, for example, reflects that maker's own dimensions and ratio families. Always read the chart supplied with the tubing you hold, or ask the supplier for the data sheet.
Sizes appear in metric millimeters and in inches, and charts built for one system may round the other. Metric tubing sizes in mm are the clearer reference when you measure with a caliper. A mm and inch conversion strip on the chart helps when a fitting or connector is listed in the other unit.
| Chart column | What it means | Why it matters |
|---|---|---|
| Supplied inner diameter | Opening before heating | Must clear the widest part you slide over |
| Recovered diameter | Opening after full shrink | Must be smaller than the part so it grips |
| Shrink ratio | How far the tubing can shrink | Sets the range of sizes one tube covers |
| Wall thickness | Material left after shrinking | Affects insulation and abrasion protection |
Finding the size for your wire or cable
Sizing heat shrink tubing starts with the largest diameter the sleeve must pass over, not the average wire size. A terminal, a connector body or a bundle of wires can be wider than the wire itself. Measure that widest point with a caliper before you open a chart.
The supplied inner diameter must sit above that measurement with a little clearance for sliding. Then check the recovered diameter against the same point, because the tubing must come down below it to hold. A size that only just clears the connector may not shrink far enough to grip the wire behind it.
For a splice, the tubing has to cover the joint and overlap the insulation on both sides. Cut the length so the overlap reaches onto sound insulation at each end. The heat shrink length for splices depends on the joint size and the overlap you want, not on the tubing size alone.
Using wire gauge to pick a tubing diameter
Wire gauge to tubing diameter tables convert an AWG number into a starting inside diameter. The heat shrink tubing size wire gauge link works because each gauge has a known conductor diameter. Insulation thickness still varies between wire types, so the gauge figure is a starting point only.
A heat shrink tubing size for 18 gauge wire is small, while a heat shrink tubing size for 14 gauge wire steps up to a larger opening. Both figures assume the tubing passes over bare or thinly insulated wire. A connector or a thicker jacket on the same gauge pushes you to the next size up.
Car stereo wiring shows why the gauge table needs a check. Heat shrink tubing size for car stereo work often covers crimped connectors and several wires together. Measure the connector body, then confirm the recovered diameter will close onto the wire bundle behind it.
How shrink ratio changes the range
The shrink ratio tells you how far a tube can reduce its diameter when heated. A 2:1 ratio brings the tubing to about half its supplied diameter at full recovery. A 3:1 or 4:1 ratio lets one size cover a wider spread of parts, which suits mixed connector and cable work.
The ratio affects how much of the chart range applies in practice. A 2:1 tube needs a part size fairly close to its supplied diameter. A 3:1 or 4:1 tube can start larger and still close onto a smaller part, so fewer sizes sit in your kit.
A heat shrink diameter ratio also ties to the wall thickness left after shrinking. Higher ratios leave a thinner wall for the same starting tube in some product lines. Read the recovered wall figure on the chart when abrasion protection matters.
Reading metric and inch sizes together
Heat shrink tubing sizes in inches and heat shrink tubing sizes mm describe the same tubing in different units. Charts often print both, and rounding between them creates small differences. Trust the unit the maker used for the nominal size and treat the other as a guide.
Metric sizes often come in round millimeter steps, which makes matching a caliper reading simple. Inch sizes follow fractional steps that suit fittings made to imperial dimensions. A heat shrink size guide in mm and inches saves a conversion step at the bench.
A heat shrink sleeve size chart used in different regions can carry the same tubing under different labels. Suppliers in South Africa, Australia and elsewhere may print local part numbers over the same dimensions. Compare the supplied and recovered diameters rather than the part number.
Wall thickness and adhesive lining
Wall thickness after shrinking decides how much mechanical and electrical protection the tubing adds. A thicker wall suits abrasion and handling, while a thin wall suits tight spaces. The chart lists this figure next to the recovered diameter.
Adhesive-lined heat shrink carries a meltable glue on the inside that fills gaps at the ends. The lining adds to the recovered wall and can change the size you need. Choose it where moisture sealing matters, such as outdoor joints or buried connections.
Cable and connector insulation sizing must account for the lining thickness on the supplied diameter. The tubing still needs clearance to slide over the part before heating. Read both the plain and lined dimensions when the chart offers them.
Checking heat shrink temperature rating
The heat shrink temperature rating tells you the range at which the tubing softens and recovers. A rating above what your heat source delivers leaves the tubing partly shrunk. A rating far below your source can damage the tubing or the part beneath it.
Apply heat evenly around the tube so it recovers along its length. Uneven heating leaves thin spots and trapped air under the sleeve. Stop when the surface smooths and the tubing hugs the part, then let it cool before you pull on it.
Some tubing families need a higher temperature than a small craft heat gun provides. Check the rating on the data sheet before you buy a size. Where a job needs a controlled heat source, a trained technician with the right tool is the safer choice.
Building the line item for an estimate
A repair estimate insulation line item needs the tubing size, the ratio and the length used. Record the supplied and recovered diameters so the choice can be checked later. This keeps the estimate clear when someone reviews the material list.
Group tubing by size and note where each size goes, such as splices, connectors or harness sections. The repair estimate insulation line item then shows why more than one size appears. A supplier quote can be matched to each line without guesswork.
Put the estimate side by side with the service provider's material list before work starts. Both documents should name the same diameters and the same shrink ratio. Any difference in size or length is worth settling before the job begins.
Heat shrink tubing sizing questions
What size heat shrink do I need for my wire?
The right size is the tubing whose supplied inner diameter clears the widest part you slide it over and whose recovered diameter closes below that part. Measure the wire or connector with a caliper, then check both numbers on the chart. A gauge table gives a starting point, but the connector often sets the real size.
How do I size heat shrink tubing for a splice?
Size heat shrink tubing for a splice by the joint diameter, then add overlap onto the insulation at each end. The supplied diameter must pass over the completed joint, and the recovered diameter must grip the wire behind it. Cut the length to cover the joint plus the overlap you choose.
What heat shrink tubing size fits 14 gauge wire?
A heat shrink tubing size for 14 gauge wire comes from a gauge table and is then confirmed against the actual wire. The table assumes bare or thinly insulated wire of that gauge. A crimped connector on the same wire needs a larger supplied diameter to slide over it.
Does a 3:1 heat shrink ratio replace two sizes?
A 3:1 heat shrink ratio covers a wider range than a 2:1 tube of the same supplied diameter. One 3:1 size can start large enough for a connector and still close onto a smaller wire. It reduces the number of sizes in a kit but still needs a diameter check on the chart.
Can I use a heat shrink size chart from another brand?
A size chart from another brand is only a rough guide, because each maker sets its own diameters and ratio families. Use the chart supplied with your tubing, or ask the supplier for the data sheet. Compare supplied and recovered diameters rather than part numbers.
How do I convert heat shrink tubing sizes in mm to inches?
Convert heat shrink tubing sizes in mm to inches by dividing the millimeter figure by 25.4, then compare the result with the chart. Rounding in either system creates small gaps, so treat one unit as nominal. The supplied and recovered diameters matter more than the label.